metal film, cylindrical resistors www.vishay.com for technical questions contact: ff3bresistors@vishay.com document number: 20006 42 revision: 15-feb-06 pmm0204 not for new designs vishay draloric features ? stable metal film on high quality ceramic ? very low tc and tight tolerances ? excellent stability at differ ent environmental conditions ? pure tin termination on nickel barrier, plated on press fit steel caps ? compatible with lead (pb)-free and lead containing soldering processes ? lead (pb)-free and rohs compliant standard electrical specifications model power rating 1) p 70 w limiting element vol tag e 2) dc or ac rms v temperature coefficient ppm/k tolerance % resistance range e-series pmm0204 0.125 100 5 0.1; 0.25 100r - 100k 96 - 192 pmm0204 0.125 100 10 0.1; 0.25 100r - 221k 96 - 192 pmm0204 0.125 100 15 0.1; 0.25 100r - 221k 96 - 192 pmm0204 0.125 100 25 0.1; 0.25 100r - 221k 96 - 192 pmm0204 0.125 100 50 0.1; 0.25 100r - 221k 96 - 192 1) permissible dissipation depends on the maximum temperature at the solder point, the component placement density and the substrate material. 2) rated voltage: . ? tc 10 ppm/c: temperature range is - 10 c to + 85 c ? without tc-band, tc marking on label only ? marking: according to iec 60062; see also datasheet ?surface mount resistor marking? (document number: 20020) p x r 3) based on measurements on test board acc. to en 140400. technical specifications parameter unit pmm0204 rated dissipation at 70 c w 0.125 limiting element voltage, dc or ac rms v 100 insulation voltage (1 min), dc or ac peak v 200 thermal resistance 3) k/w 220 insulation resistance ? 10 10 category temperature range c - 10 to + 100 failure rate 10 -9 /h < 1 weight/1000 pcs g 18
document number: 20006 for technical ques tions contact: ff3bresistors@vishay.com www.vishay.com revision: 15-feb-06 43 pmm0204 metal film cylindrical resistors vishay draloric dimensions * d measured in the middle of the resistor model dimensions [in millimeters] d max d* l a max a min pmm0204 1.4 d - 0.15 3.6 - 0.15 0.85 0.5 model solder pad dimensions [in millimeters] reflow soldering wave soldering ab l abl pmm0204 1.0 1.6 2.2 1.2 1.6 2.2 note 1. products can be ordered using either the product description or the part number. 2. the part number is shown to facilitate the introduction of a unified part numbering system. cu rrently, this part number is ap plicable in the americas only. 3. please refer to table packing, see below. part number and pr oduct description 1) part number 2) : pmm02040e5620cb0 model/size special character tc value tolerance packing 3) special pmm0204 0 = neutral g = 5 ppm/k f = 10 ppm/k e = 15 ppm/k d = 25 ppm/k c = 50 ppm/k 3 digit value 1 digit multiplier 0000 = jumper multiplier 0 = *10 0 1 = *10 1 2 = *10 2 3 = *10 3 b = 0.1 % c = 0.25 % b1 b3 b0 m3 up to 2 digits 00 = standard product description: pmm0204 15 562r 0.25% b0 pmm0204 15 562r 0.25 % b0 model tc resistance value tolerance packing 3) pmm0204 5 ppm/k 10 ppm/k 15 ppm/k 25 ppm/k 50 ppm/k 100r = 100 221k = 221k 0.1 % 0.25 % b1 b3 b0 m3 02 m m p040e5620cb000
www.vishay.com for technical questions contact: ff3bresistors@vishay.com document number: 20006 44 revision: 15-feb-06 pmm0204 vishay draloric metal film cylindrical resistors * for tc 25 ppm/k and tolerance 0.25 % only. further information about packing, see also datasheet ?s urface mount resistor pac king? (document number: 20014) packing model blister tape on reel acc. iec 60286-3 bulk case acc. iec 60286-6 diameter pieces/reel code pieces/ bulk case code pmm0204 180 mm/7" 1000 b1* 3000 m3 180 mm/7" 3000 b3 330 mm/13" 10000 b0 - 55 - 25 0 25 50 75 100 0 20 40 60 8 0 100 120 derating ambient temperature in c rated power in % 70 1k 5k 10k 50k 100k 500k 1m 0.01 0.03 0.05 0.1 0.3 0.5 1 2 3 current noise resistance value in current noise in v/v performance test conditions of test test results endurance test at 70 c iec 60115-1, 4.25.1 1000 hours at 70 c, 1.5 hours "on", 0.5 hours "off" 0.1 % endurance at uct iec 60115-1, 4.25.3 1000 hours at 125 c without load 0.1 % overload test iec 60115-1, 4.13 short time overload for 2 seconds 2.5 x rated voltage or 2 x limiting element voltage 0.02 % thermal shock iec 60115-1, 4.19 and iec 60068-2-14 rapid change between upper and lower category temperature, 5 cycles 0.02 % damp heat steady state iec 60115-1, 4.24 and iec 60068-2-78 56 days at 40 c and 93 % relative humidity 0.2 % resistance to soldering heat iec 60115-1, 4.18 and iec 60068-2-58 10 seconds at 260 c solder bath temperature 0.05 %
document number: 20006 for technical ques tions contact: ff3bresistors@vishay.com www.vishay.com revision: 15-feb-06 45 pmm0204 metal film cylindrical resistors vishay draloric applicable specifications ? en 140401-803 ? en 140400 ? en 60115-1
document number: 91000 www.vishay.com revision: 18-jul-08 1 disclaimer legal disclaimer notice vishay all product specifications and data are subject to change without notice. vishay intertechnology, inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, ?vishay?), disclaim any and all liability fo r any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. vishay disclaims any and all li ability arising out of the use or application of any product describ ed herein or of any information provided herein to the maximum extent permit ted by law. the product specifications do not expand or otherwise modify vishay?s terms and conditions of purcha se, including but not limited to the warranty expressed therein, which apply to these products. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of vishay. the products shown herein are not designed for use in medi cal, life-saving, or life-sustaining applications unless otherwise expressly indicated. customers using or selling vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify vishay for any damages arising or resulting from such use or sale. please contact authorized vishay personnel to obtain written terms and conditions regarding products designed for such applications. product names and markings noted herein may be trademarks of their respective owners.
|
